News

how to use Realy Tech COVID Rapid test instructions

There are about 500k tests Rapid test arrive in our German warehouse everyweek.


Realy Tech COVID Rapid test instructions

Realy Tech rapid test how to use


A Novel Coronavirus (SARS-Cov-2) Antigen Rapid Test Device (Saliva)

r25-300x300.jpg


Allow the test device, specimen, extraction buffer to equilibrate to room temperature(15-30°C) prior to testing. Do not place anything in the mouth including food, drink, gum,tobacco, water and mouthwash products for at least 10 minutes prior to collection of oral fluid specimen.


1. Spit enough saliva into the saliva collect cup/bag.


2. Take out an extraction tube and a bottle of extraction buffer, remove the extraction buffer bottle cap, add all the extraction buffer into the extraction tube.


3. Draw enough saliva from the cup with a dropper, make sure the liquid level does not exceed the tunnel between the lower air bag and the plastic pipe, transfer all saliva in the plastic pipe into the extraction tube.


4. Take out a nozzle and close into the extraction tube, gently shake the extraction tube vertically for about 5 seconds to allow saliva mix well with extraction buffer. Fold the used cup/bag in half and discard it into the plastic bag as medical waste in accordance with local regulations.


ss-2.png


5. Remove the test device from the sealed foil pouch and use it as soon as possible. Best results will be obtained if the assay is performed immediately after opening the foil pouch. Put the test device on a clean and flat surface. Transfer 3 drops of sample into the sample well of test device vertically, start the timer.


6.Read the result at 10~20 minutes. Don’t interpret the result after 20 minutes.

ss-1.png


【INTERPRETATION OF RESULTS】


POSITIVE: Two red lines appear. One red line appears in the control region(C), and one red line in the test region(T). The shade of color may vary,but it should be considered positive whenever there is even a faint line.


NEGATIVE: Only one red line appears in the control region(C), and no line in the test region(T).


The negative result indicates that there are no Novel coronavirus particles in the sample or the number of viral particles is below the detectable range.


INVALID: No red line appears in the control region(C). The test is invalid even if there is a line ontest region(T). Insufficient sample volume or incorrect procedural techniques are the most likely reasons for control line failure. Review the test procedure and repeat the test using a new test device. If the problem persists, discontinue using the test kit immediately and contact your local distributor.


【FEATURES】


Specimen type: Saliva

Testing time: 10 minutes

Sensitivity: 93.9%

Specificity:> 99.58%


Rapid test instructions VIDEO



B Novel Coronavirus (SARS-Cov-2) Antigen Rapid Test(Swab)

r-300x300.jpg

Allow the test, specimen, extraction buffer to equilibrate to room temperature (15-30°C)

prior to testing.

1. Completely insert the sterilized swab supplied in this kit into the nasal basin, and swab several times to collect the epidermal cells of the mucus.

2. Unscrew the whole cap of the specimen collection tube, take out 1 bottle of Sample Extraction Buffer, remove the bottle cap, add all the extraction buffer into the extraction tube.

3.Place the sterilized swab specimen in the sample extraction buffer. Rotate the swab for approximately 10 seconds while pressing the head against the inside of the tube to release the antigen in the swab.

4.Remove the sterilized swab while squeezing the sterilized swab head against the inside of Buffer as you remove it to expel as much liquid as possible from the swab. Discard the sterilized swab in accordance with your biohazard waste disposal protocol.

5. Screw on and tighten the cap onto the specimen collection tube, then shake the specimen collection tube vigorously to mix the specimen and the sample extraction buffer. See illustration 4.

cov-2.png
When the sample is ready, take the following procedures to complete the test:

1, Remove the test device from the sealed foil pouch and use it as soon as possible. Best results will be obtained if the assay is performed immediately after opening the foil pouch. Put the test device on a clean and flat surface.

2, Transfer 3 drops of sample into the sample well of test device vertically, start the timer, read the result at 10~20 minutes. Don’t interpret the result after 20 minutes.

cov-3.png
【FEATURES】

Specimen types: Nasopharyngeal swab
Testing time: 10-15 minutes
Sensitivity: 96.17%
Specificity:> 99.9%

No previous NEXT:EU declaration of conformity

RELATED NEWS

CATEGORIES

CONTACT US

Contact: Stephen

Phone: +86-18123902349

E-mail: [email protected]

Add: Shenzhen,Guangdong Province, China